S |
M |
T |
W |
T |
F |
S |
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
4 members (SKB, Mike Harrell, Lloyd3, 1 invisible),
766
guests, and
4
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,445
Posts544,858
Members14,406
|
Most Online1,258 Mar 29th, 2024
|
|
|
Joined: Jul 2008
Posts: 161 Likes: 14
Sidelock
|
OP
Sidelock
Joined: Jul 2008
Posts: 161 Likes: 14 |
Does anyone have information on reloading AA hulls with fiber wads?
|
|
|
|
Joined: Mar 2011
Posts: 4,080 Likes: 466
Sidelock
|
Sidelock
Joined: Mar 2011
Posts: 4,080 Likes: 466 |
In the past few weeks, I've looked into the feasibility of handloading with fiber. As long as the hulls aren't tapered but are straight walled you are good to go. The AA's are straight walled (base isn't). The old Lyman Ideal Handbooks have recipes and directions for loading fiber wads. I have a 1953 Handbook, #39 that contains directions and recommended loads but most of the powders, other than Hercules Red Dot, are unrecognizable by me. (I don't know if the 1953 recipe for Red Dot is what we have now.) According to the manual, felt height (thickness) above the nitro cards should be approximately 3/4ths of bore diameter which is the compromise between 1/2 of bore and not exceeding bore diameter. Shell trimming maybe required to conform to this restriction. Plastic wad recipes are interchangeable with the felt, but a 5% increase in powder drop is recommended. Per powder is a recommended amount of pressure to be applied during seating. For instance, with Red Dot, 10-12 gauges require 70 lbs. Smaller gauges, 60. Sources on the internet (it's gotta be correct if on the internet. ) report 30-40 lbs. is adequate. I've seen where Ballistic Products has (maybe had) a flyer regarding loading with fiber wads and that may be the best resource for tested recipes and current powders. Gil
|
|
|
|
Joined: Feb 2013
Posts: 644 Likes: 3
Sidelock
|
Sidelock
Joined: Feb 2013
Posts: 644 Likes: 3 |
Gentlemen,
Is the benefit of using fiber wads to gain better patterns in older guns with tighter chokes?
|
|
|
|
Joined: Jun 2008
Posts: 5,532 Likes: 169
Sidelock
|
Sidelock
Joined: Jun 2008
Posts: 5,532 Likes: 169 |
Has Illinois gone non-tox for all hunting?
USAF RET 1971-95
|
|
|
|
Joined: Mar 2011
Posts: 4,080 Likes: 466
Sidelock
|
Sidelock
Joined: Mar 2011
Posts: 4,080 Likes: 466 |
Caleb, that may be a benefit, but my interest is just doing it for the hell of it. That and looking to spend more time cleaning gun barrels from lead fouling....Gil
|
|
|
|
Joined: Feb 2013
Posts: 644 Likes: 3
Sidelock
|
Sidelock
Joined: Feb 2013
Posts: 644 Likes: 3 |
Thanks Gil...I hope you're enjoying that retirement!
|
|
|
|
Joined: Apr 2005
Posts: 1,688 Likes: 31
Sidelock
|
Sidelock
Joined: Apr 2005
Posts: 1,688 Likes: 31 |
Sorry to maybe upset my American cousins. Fibre wadded , paper cased cartridges are far ,far better for the environment . Better close range patterns may also interest some of you heathens.
|
|
|
|
Joined: Mar 2011
Posts: 4,080 Likes: 466
Sidelock
|
Sidelock
Joined: Mar 2011
Posts: 4,080 Likes: 466 |
Salopian, Naw, didn't upset me. Trashin' up the lowcountry woods is a longstanding redneck tradition. Or so it seems judging from the beer cans, etc. I see in some places. Yesterday I found a Samsung Galaxy phone in a dried up mud puddle. Properly broken by someone's mudgrip tires. Gil
|
|
|
|
Joined: Mar 2016
Posts: 287 Likes: 7
Sidelock
|
Sidelock
Joined: Mar 2016
Posts: 287 Likes: 7 |
AA HS hulls are straight walled above the base reinforcement. If the powder fills beyond the lip you are good to go. Needless to say, Black Powder and fibre wads work great.
|
|
|
|
Joined: Dec 2001
Posts: 12,743
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 12,743 |
When I began reloading card & fiber or felt was about all there was. If you are going for real fast production it's not quite as fast as popping in a one-piece plastic wad. Most of the really bad leading comes about from an overbore or long cone, either of which allows blowby which melts some lead. With a standard bore & cone, I never had any problem with leading that a bore brush wouldn't take care of. I did at that time use the "Ring-Waxed" fiber filler wads which also help resist leading.
Plastic hulls & plastic wads both began to hit the US market in the 1960s. In the beginning, there were several plastic obturating cup wads which were still used with filler wads. WW even brought out a line of shells which used a cardboard cupped wad in conjunction with a plain wrapper for the shot.
By the 1970s the one-piece plastic wads had pretty well taken over the field, due mainly to their ease in loading. What many did not realize then & still don't is they did not truly increase the choke effect. For the most part, a given choke would show a slightly higher pattern percentage, but this was primarily from bringing in the deformed & useless shot from the fringes, not an actual reduction of the "Killing Circle" of the original pattern.
Miller/TN I Didn't Say Everything I Said, Yogi Berra
|
|
|
|
Joined: Jan 2004
Posts: 6,705 Likes: 406
Sidelock
|
Sidelock
Joined: Jan 2004
Posts: 6,705 Likes: 406 |
I reload AAs with fiber wads. I do so with blackpowder however. they work just fine. I haven't had much leading even if I forgo the mylar wrap or paper wrap.
I prefer to use wads that are well lubed in hopes that they are less likely to smolder. In some conditions, I will go back to smokeless and plastic wads to avoid fire issues.
The biggest problem I have had with them is that they are not really very consistent with regards to thickness which makes for issues with crimping, either folded or roll crimped.
_________ BrentD, (Professor - just for Stan)
|
|
|
|
Joined: Jan 2008
Posts: 342
Sidelock
|
Sidelock
Joined: Jan 2008
Posts: 342 |
I spent several months loading for the best 16 Ga. loads using RMC all brass hulls in my #2 AyA. My best patterns came from card and fiber wads, not 1-piece plastic wads and beautiful patterns they are!!
Jim
|
|
|
|
Joined: Jan 2002
Posts: 598 Likes: 58
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 598 Likes: 58 |
I am interested in using brass shells and fiber wads with bismuth for waterfowl. As per Salopian above, I have read that fiber wads produce good short range patterns, but how about longer range for ducks?
|
|
|
|
Joined: Jan 2004
Posts: 6,705 Likes: 406
Sidelock
|
Sidelock
Joined: Jan 2004
Posts: 6,705 Likes: 406 |
I killed a couple giant Canadas with fiber and Bi2's. Seemed fine but I did not pattern them.
_________ BrentD, (Professor - just for Stan)
|
|
|
|
Joined: Apr 2005
Posts: 1,688 Likes: 31
Sidelock
|
Sidelock
Joined: Apr 2005
Posts: 1,688 Likes: 31 |
LGF, Over here in the UK we use fibre wads and steel shot for Ducks & Geese without too many issues. Need a mylar wrap to save bore damage with steel. But there are many videos on Youtube showing birds being shot at 70 yards plus using fibre wadded cartridges.
|
|
|
|
Joined: Jan 2008
Posts: 342
Sidelock
|
Sidelock
Joined: Jan 2008
Posts: 342 |
LGF wrote: but how about longer range for ducks? I have patterned my 16 Ga. at the distances I shoot using card & fiber wads with excellent results. The ranges vary depending on chokes. Using NP hard shot: 22 yards - 37 yards using the IC barrel & 30 - 42 yards with the Mod barrel. Suggest that you load up a few and pattern them.
Last edited by wyobirds; 01/15/19 04:24 PM.
Jim
|
|
|
|
Joined: Jul 2008
Posts: 161 Likes: 14
Sidelock
|
OP
Sidelock
Joined: Jul 2008
Posts: 161 Likes: 14 |
Does anyone have specific information regarding data for AA hulls for clay targets? Many years ago the Ljutic mono wad was used as a replacement for the AA wad. Does such a thing still exist? What about fiber wads for reloading light loads such as 7/8 ot 3/4 oz? Does anyone in the UK reload Gamebore or Kent shells with fiber wads? Thanks in advance.
|
|
|
|
Joined: Apr 2005
Posts: 1,688 Likes: 31
Sidelock
|
Sidelock
Joined: Apr 2005
Posts: 1,688 Likes: 31 |
Many reloaders here in the UK use Gamebore shells for reloading. a forum called PigeonwatchUK has a reloaders section , members on there will provide recipes and information for reloading fibre wadded cartridges . Although we use many different powders here I am sure some useful information can be gleaned.
|
|
|
|
Joined: Jul 2008
Posts: 161 Likes: 14
Sidelock
|
OP
Sidelock
Joined: Jul 2008
Posts: 161 Likes: 14 |
Thanks for the lead salopian.
|
|
|
|
|