S |
M |
T |
W |
T |
F |
S |
|
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
|
|
1 members (btbell),
305
guests, and
5
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,615
Posts547,014
Members14,427
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Jan 2002
Posts: 7,705 Likes: 103
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,705 Likes: 103 |
In times past, I have posted this picture of the exploded original 32inch barrel set to my L.C. Smith 12ga Specialty grade gun. Even though I have a shorter replacement barrel set from an O grade, I always wanted to have the original set re-done. I asked Aaron Little to let me have some pictures of the progress. His response was that the sleeving process was not very photogenic, but sent me the pics below anyway: Photogenic or not, I'd have to say my barrels look a whole lot better now than when I sent them to Mr. Little!...Geo
|
|
|
|
Joined: Jun 2008
Posts: 5,539 Likes: 170
Sidelock
|
Sidelock
Joined: Jun 2008
Posts: 5,539 Likes: 170 |
Awesome progress Your first picture made my heart ill! Mike
Last edited by skeettx; 02/16/17 03:42 PM.
USAF RET 1971-95
|
|
|
|
Joined: Jun 2008
Posts: 2,738 Likes: 97
Sidelock
|
Sidelock
Joined: Jun 2008
Posts: 2,738 Likes: 97 |
Out of interest;, but it may have been covered before, how did the barrels come to split in the first place? Just curious. Lagopus.....
|
|
|
|
Joined: Nov 2006
Posts: 1,659 Likes: 77
Sidelock
|
Sidelock
Joined: Nov 2006
Posts: 1,659 Likes: 77 |
Very interesting. I for one would love to see how they turn out.
Mike Proctor
|
|
|
|
Joined: Jan 2002
Posts: 7,705 Likes: 103
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,705 Likes: 103 |
Out of interest;, but it may have been covered before, how did the barrels come to split in the first place? Just curious. Lagopus..... I don't know and the guy I bought it from didn't either. I'm guessing it was an obstruction burst. The markings inside the split look to me like something an expert witness would have put there to facilitate an explanation to a court of law. I would love to have a transcript of the hearing. The barrel edges are very thin, but that could be a result of stretching when the burst occurred...Geo
|
|
|
|
Joined: Apr 2008
Posts: 63
Sidelock
|
Sidelock
Joined: Apr 2008
Posts: 63 |
Geo
Does his process involve TIGing those seems at the chambers and forward of the forcing cones?
Looks good. It will feel like a new gun!
Jason
|
|
|
|
Joined: Jan 2002
Posts: 7,705 Likes: 103
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,705 Likes: 103 |
Yes, Mr. Little is welding where the tube is attached to present a seamless joint. That will probably cause a slight discoloration when the barrels are re-blued, but I'd prefer that to an open seam.
I will post additional pictures as they come available...Geo
|
|
|
|
Joined: Apr 2016
Posts: 830 Likes: 37
Sidelock
|
Sidelock
Joined: Apr 2016
Posts: 830 Likes: 37 |
Very good to know! I cant wait to see how it turns out
|
|
|
|
Joined: Feb 2011
Posts: 1,405
Sidelock
|
Sidelock
Joined: Feb 2011
Posts: 1,405 |
If done properly, a soldered joint would not be "open" but just as undetected as a welded joint if even less so. If the right filler rod is used on the weld, the rust blue should hide the weld well.
B.Dudley
|
|
|
|
Joined: Jan 2006
Posts: 9,443 Likes: 320
Sidelock
|
Sidelock
Joined: Jan 2006
Posts: 9,443 Likes: 320 |
Before blueing courtesy of Toby Barclay After Not so good
|
|
|
|
|