|
S |
M |
T |
W |
T |
F |
S |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
|
8 members (Der Ami, SKB, MattH, 3 invisible),
310
guests, and
2
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,923
Posts550,751
Members14,459
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Jan 2002
Posts: 865
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 865 |
Hi All, Would or should you apply grease to some paerts of a sidelock? If so which parts? I have included a photo of the inside of the lock and trigger. All opinions and help appreciated. Thanks, Jeff G.
|
|
|
|
Joined: Jul 2004
Posts: 287
Sidelock
|
Sidelock
Joined: Jul 2004
Posts: 287 |
With this sort of thing I just mix up a good 2 stroke fuel mix (top quality 2stroke oil) 1/2 pint to 1 gallon, wash the whole thing in and let the unleaded petrol totally evaporate, the film of oil left is all you need, Heavy greases and oils can make things sluggish, cause double or accidental discharges and all sorts of problems
Hotrack
Life is too short to drink cheap wine
|
|
|
|
Joined: Dec 2002
Posts: 659
Sidelock
|
Sidelock
Joined: Dec 2002
Posts: 659 |
I just give it a shot of RemOil or Break Free.
|
|
|
|
Joined: Jan 2002
Posts: 5,954 Likes: 12
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 5,954 Likes: 12 |
A periodic and judicious shot of oil will keep it running smooth and free. These bearing points are mostly low speed, relatively light pressure, and relatively low frequency, so lube is not so critical. Hard steel on hard steel is not going to wear for a long time/lot of cycles. Grease is better on more open bearings. You are more likely to over oil and saturate the stock head than to under oil.
|
|
|
|
Joined: Feb 2004
Posts: 13,880 Likes: 16
Sidelock
|
Sidelock
Joined: Feb 2004
Posts: 13,880 Likes: 16 |
If you are not disassembling the lock, I'd clean by soaking/ultrasonic cleaner with mineral spirits, acetone, or lacquer thinner, dry with compressed air and then do as the others have suggested with a light oil followed by blowing off the locks with compressed air and wipe exess. I'd put a small dab of your favorite high pressure auto grease on the contact point of the cocking rod to hammer.
|
|
|
|
Joined: Jan 2002
Posts: 5,983
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 5,983 |
I like a dot of grease on sear notches, cocking lever parts, leaf spring stirrups and other hard working spots like barrel pivot pins, rear of forend iron. small quantity of good quality oil on pivoting areas like hammer axles, sear pivot screws, etc. As Rocket said, don't overdo it. You don't want oil running into the stock wood. A good reason to store guns muzzle down, in your safe or cabinet.
> Jim Legg <
|
|
|
|
Joined: Jan 2002
Posts: 865
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 865 |
Hi Guys,
Thanks for the advice.
Jeff G.
|
|
|
|
Joined: Jan 2002
Posts: 674
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 674 |
What type of gun is that?
skunk out
|
|
|
|
Joined: Jun 2004
Posts: 986
Sidelock
|
Sidelock
Joined: Jun 2004
Posts: 986 |
I would save the grease for the trunions and/or hinge pin. The action looks very nice, what type/model of gun is that?
|
|
|
|
Joined: Jan 2002
Posts: 865
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 865 |
Hi Mark & JM. It is a gun purchased on this site. M. Fabrizioli Figli 16 ga o/u. There was a long thread about it on this site Custom Italian O/U. It is a 16 ga , I shoot it well. After a little work I am happy with it. Jeff G.
|
|
|
|
|
|