|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
1
|
2
|
3
|
4
|
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
|
Forums10
Topics39,492
Posts562,051
Members14,585
| |
Most Online9,918
Jul 28th, 2025
|
|
|
|
Joined: Jul 2012
Posts: 4,939 Likes: 342
Sidelock
|
Sidelock
Joined: Jul 2012
Posts: 4,939 Likes: 342 |
R.Marshall,
I have come to the painful conclusion that I don't know what the heck it is chambered for now. It seems to have been chambered for a standard early German cartridge and underwent some unfortunate attempt at rechambering to something that was available, and is now unidentifiable. If it were mine, I would fireform a couple more 6.5x55 Norma cases, "slug" the barrel to insure it is 6.5mm(.264" about) and send the fireformed cases to CH4D to have them make a set of dies to fit the chamber. Then you can treat it like a wildcat, load to 6.5x57 pressures, call it whatever suits you( 6.5 Marshall special?) and kill a pickup truck load of deer with it.
Mike
|
|
|
|
|
Joined: Oct 2015
Posts: 185 Likes: 3
Sidelock
|
|
OP
Sidelock
Joined: Oct 2015
Posts: 185 Likes: 3 |
Mike thanks for your help as always and everyone else that has replied with advice.
|
|
|
|
|
Joined: Dec 2001
Posts: 7,308 Likes: 614
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 7,308 Likes: 614 |
You might try just neck sizing after fire forming and can likely use 6.5x55 dies or something similar set so they do not resize the case. As long as you do not own two rifles in the same caliber this method works very well.
Steve
Firearms imports, consignments ![[Linked Image from i.imgur.com]](https://i.imgur.com/Ez9oz9Rl.jpg)
|
|
|
|
|
Joined: Oct 2015
Posts: 185 Likes: 3
Sidelock
|
|
OP
Sidelock
Joined: Oct 2015
Posts: 185 Likes: 3 |
Thanks Steve, that sounds like a good method. Thanks for all your help.
|
|
|
|
|
Joined: Dec 2001
Posts: 7,308 Likes: 614
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 7,308 Likes: 614 |
You are more than welcome. If you use the neck sizing technique be sure not to move the shoulder on the fire formed case.
Steve
Firearms imports, consignments
|
|
|
|
|
Joined: Jul 2012
Posts: 4,939 Likes: 342
Sidelock
|
|
Sidelock
Joined: Jul 2012
Posts: 4,939 Likes: 342 |
SKB, R.Marshall
I use that neck sizing trick for several of my rifles, even sometimes shortening the sizing die. I don't believe it will work in this case, because the fireformed cases seem to be "blown out" larger than the normal 6.5x55 chamber. If you have a die set made to fit, then it could be used to neck size for other rifles. Of course, as always, I could be wrong.
Mike
|
|
|
|
|
Joined: Dec 2001
Posts: 7,308 Likes: 614
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 7,308 Likes: 614 |
A larger body die may then work, 6.5/06 etc. just have to play around with it but I think something may work in place of a custom die. I as well could be wrong.
Steve
Last edited by SKB; 01/01/20 12:03 PM.
Firearms imports, consignments
|
|
|
|
|
Joined: Jul 2012
Posts: 4,939 Likes: 342
Sidelock
|
|
Sidelock
Joined: Jul 2012
Posts: 4,939 Likes: 342 |
Steve,
06 diameter is smaller than 6.5x55, maybe 6.5 Rem. Mag., but they are pretty rare too. I know custom dies are pretty pricy, I had to have one made to form 6.5x58R S&S cases in a couple steps. I made up one for fireforming with about 5 different dies. It formed OK but it was more trouble than it was worth for a rifle I planned to keep.
Mike
Last edited by Der Ami; 01/01/20 01:28 PM.
|
|
|
|
|
|
|
