doublegunshop.com - home Forums General Discussion DoubleGun BBS @ doublegunshop.com Amazed at machining on Sauer Sidelock hammergun

October
S	M	T	W	T	F	S
			1	2	3	4
5	6	7	8	9	10	11
12	13	14	15	16	17	18
19	20	21	22	23	24	25
26	27	28	29	30	31

Who's Online Now

2 members (NTaxiarchis, Mills), 429 guests, and 4 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums10

Topics39,491

Posts562,017

Members14,584

Most Online9,918
Jul 28th, 2025

Print Thread

Re: Amazed at machining on Sauer Sidelock hammergun Rd Show #134801 02/07/09 09:29 PM
Joined: Mar 2006 Posts: 104 Laurel Mountains of Pa RGS022 OP Junior Member
OP RGS022 Junior Member Joined: Mar 2006 Posts: 104 Laurel Mountains of Pa	Rich, Probably an hour or so. I am about 5 miles from Fort Ligonier. Screwdriver through the finger came from a frozen discharge line on a waste water pump. The screw head twisted right off, the screwdriver dug right in to my finger. Last edited by RGS022; 02/07/09 10:18 PM. I can't be too bad, my dogs will kiss me.

Entire Thread
Subject	Posted By	Posted
Amazed at machining on Sauer Sidelock hammergun	RGS022	02/08/09 12:05 AM
Re: Amazed at machining on Sauer Sidelock hammergun	Rd Show	02/08/09 01:15 AM
Re: Amazed at machining on Sauer Sidelock hammergun	RGS022	02/08/09 01:29 AM
Re: Amazed at machining on Sauer Sidelock hammergun	NiklasP	02/08/09 01:50 AM
Re: Amazed at machining on Sauer Sidelock hammergun	RGS022	02/08/09 02:30 AM
Re: Amazed at machining on Sauer Sidelock hammergun	QTRHRS	02/08/09 04:47 AM
Re: Amazed at machining on Sauer Sidelock hammergun	GregSY	02/08/09 04:58 AM
Re: Amazed at machining on Sauer Sidelock hammergun	NiklasP	02/08/09 05:33 PM
Re: Amazed at machining on Sauer Sidelock hammergun	Puddle Rat	02/08/09 11:03 PM
Re: Amazed at machining on Sauer Sidelock hammergun	RGS022	02/08/09 11:33 PM
Re: Amazed at machining on Sauer Sidelock hammergun	Puddle Rat	02/10/09 12:26 AM
Re: Amazed at machining on Sauer Sidelock hammergun	RGS022	02/10/09 06:23 AM
Re: Amazed at machining on Sauer Sidelock hammergun	bill schodlatz	02/10/09 03:03 PM
Re: Amazed at machining on Sauer Sidelock hammergun	RGS022	02/11/09 02:21 AM
Re: Amazed at machining on Sauer Sidelock hammergun	Daryl Hallquist	02/11/09 03:10 AM
Re: Amazed at machining on Sauer Sidelock hammergun	RGS022	02/11/09 03:55 AM

Link Copied to Clipboard

Updated every minute of everyday!

Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 1.021s Queries: 17 (0.481s) Memory: 0.8256 MB (Peak: 1.9025 MB) Data Comp: Off Server Time: 2025-10-06 16:01:01 UTC
Valid HTML 5 and Valid CSS