|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
1
|
2
|
3
|
4
|
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
|
1 members (welder),
739
guests, and
4
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums10
Topics39,490
Posts562,009
Members14,584
| |
Most Online9,918
Jul 28th, 2025
|
|
|
|
Joined: Mar 2006
Posts: 104
Junior Member
|
OP
Junior Member
Joined: Mar 2006
Posts: 104 |
I am getting ready to try to repair my Sauer stock that had been repaired previously. It looks like the Accraglass just separated as there is a crystaline residue on both pieces. What will remove the remnants? The two pieces do not fit together perfectly due to interference where the glue remains on both pieces.
I can't be too bad, my dogs will kiss me.
|
|
|
|
|
Joined: Mar 2002
Posts: 3,269 Likes: 459
Sidelock
|
|
Sidelock
Joined: Mar 2002
Posts: 3,269 Likes: 459 |
Hammer and chisel. No joke.
JR
Be strong, be of good courage.
God bless America, long live the Republic.
|
|
|
|
|
Joined: May 2005
Posts: 482
Sidelock
|
|
Sidelock
Joined: May 2005
Posts: 482 |
will very high heat do anything to it? (as you might get in bending, etc--not talking about burning the stock)
|
|
|
|
|
Joined: Dec 2001
Posts: 6,457 Likes: 336
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 6,457 Likes: 336 |
Years ago I removed some Herter's Glass Bedding with paint remover . It actually worked quite well.
|
|
|
|
|
Joined: Feb 2008
Posts: 11,785 Likes: 673
Sidelock
|
|
Sidelock
Joined: Feb 2008
Posts: 11,785 Likes: 673 |
Most epoxies begin softening and breaking down between 160-180 degrees F. A few will hold out above 220 F, but I believe most all will soften below the scorching point of walnut. Careful heating and scraping the residue without damaging the mating surfaces may get you where you want to go. Sounds like some doweling or extra reinforcement may prevent a third trip down this road. Just wondering though, are you sure it's Acraglas?
Voting for anti-gun Democrats is dumber than giving treats to a dog that shits on a Persian Rug
|
|
|
|
|
Joined: Dec 2008
Posts: 571 Likes: 9
Sidelock
|
|
Sidelock
Joined: Dec 2008
Posts: 571 Likes: 9 |
Heat will soften it. I just had that problem a couple of weeks ago. I used a pencil torch to apply the heat as you can control where you apply the heat easier. JUst lightly heat the surface and it will scrape off.
|
|
|
|
|
Joined: Dec 2001
Posts: 2,961 Likes: 9
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 2,961 Likes: 9 |
If you can get the metal out yuor wife's microwave will do the job.
Go slow!
bill
|
|
|
|
|
Joined: Jan 2002
Posts: 527
Sidelock
|
|
Sidelock
Joined: Jan 2002
Posts: 527 |
Personally I would soak it out / off with acetone, the epoxy didn't bind to the wood in the first place and chances are will not do so again. I would think oil could be the culprit, soaking the head of the stock and all the pieces in acetone would also remove any oil. You would not have to soak the whole stock unless you refinishing the whole thing. Just a thought, FWIW --- John Can.
|
|
|
|
|
Joined: Jan 2002
Posts: 792 Likes: 36
Sidelock
|
|
Sidelock
Joined: Jan 2002
Posts: 792 Likes: 36 |
A soak in denatured alcohol will do it. 24 hrs or so will soften it right up. Won't harm wood or metal but will damage wood finish. The only other good option is gentle heat. Good luck.
|
|
|
|
|
Joined: Dec 2001
Posts: 6,457 Likes: 336
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 6,457 Likes: 336 |
One might use any of the above methods to remove the Acraglass, but you can control paint remover so it does not affect the finishes around it.
|
|
|
|
|
|
|
