|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
|
|
|
1
|
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
|
30
|
|
|
|
|
|
|
|
|
2 members (Chantry, Carcano),
389
guests, and
4
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums10
Topics39,555
Posts562,737
Members14,594
| |
Most Online9,918
Jul 28th, 2025
|
|
|
|
Joined: Apr 2004
Posts: 869
Sidelock
|
OP
Sidelock
Joined: Apr 2004
Posts: 869 |
How on earth is it attached?
Thanks,
Mark
 Ms. Raven
|
|
|
|
|
Joined: Mar 2012
Posts: 369 Likes: 40
Sidelock
|
|
Sidelock
Joined: Mar 2012
Posts: 369 Likes: 40 |
Most likely glued on. What brand gun? Butt plate or recoil pad...I assume you said what you mean.
Last edited by SamW; 05/11/12 01:06 PM.
Sam Welch
|
|
|
|
|
Joined: Mar 2005
Posts: 680
Sidelock
|
|
Sidelock
Joined: Mar 2005
Posts: 680 |
Jostam made a couple of recoil pads that were attached by first securing a rubber base plate to the butstock with brass brads and then using rubber cement to attach the pad to the base.
|
|
|
|
|
Joined: Nov 2006
Posts: 3,477 Likes: 54
Sidelock
|
|
Sidelock
Joined: Nov 2006
Posts: 3,477 Likes: 54 |
Some newer guns apparently have interchangeable butt pads that snap on and off a fitting on the butt of the gun. I don't own any of these, but I think some of the Beretta Gel Tek pads are snap-ons. And I think I read that some of the CSMC RBL's had interchangeable pads.
|
|
|
|
|
Joined: Aug 2008
Posts: 978 Likes: 51
Sidelock
|
|
Sidelock
Joined: Aug 2008
Posts: 978 Likes: 51 |
NEGC makes detachable pads that work really well. I suppose a metal butt plate could be so configured if you welded studs on the back and plugged/filed the screw holes.
|
|
|
|
|
Joined: May 2010
Posts: 1,545 Likes: 106
Sidelock
|
|
Sidelock
Joined: May 2010
Posts: 1,545 Likes: 106 |
Are we talking modern or old ?
|
|
|
|
|
Joined: Apr 2004
Posts: 869
Sidelock
|
|
OP
Sidelock
Joined: Apr 2004
Posts: 869 |
Sorry for the delay...we are talking old, 1911 Webley old.
Thin, single layer horn or "hard rubber".
Glue would seem out of place?
Thank you,
Mark
Ms. Raven
|
|
|
|
|
Joined: Nov 2006
Posts: 3,477 Likes: 54
Sidelock
|
|
Sidelock
Joined: Nov 2006
Posts: 3,477 Likes: 54 |
Glue would seem out of place? If it is original 1911, I'd bet on hide glue.
|
|
|
|
|
Joined: Apr 2004
Posts: 869
Sidelock
|
|
OP
Sidelock
Joined: Apr 2004
Posts: 869 |
Thanks, I did not know that was an option.
Any idea what would be detrimental to it?
The gun had a lace-up pad on it and it soaked/abraided some of the oil finish up. I rubbed some linseed and alkenet into it and it looks much better...would hate to undo things though!
Mark
Ms. Raven
|
|
|
|
|
Joined: Nov 2006
Posts: 3,477 Likes: 54
Sidelock
|
|
Sidelock
Joined: Nov 2006
Posts: 3,477 Likes: 54 |
Any idea what would be detrimental to it? The usual way to break or clean up a hide glue joint is to use heat or water or some combination of the two (i.e., boiling water). Linseed oil and stain should not damage the joint if applied carefully.
|
|
|
|
|
|
|
