|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
|
1
|
2
|
3
|
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
4 members (terc, SKB, Nitrah, j7l2),
289
guests, and
14
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums10
Topics39,808
Posts565,933
Members14,620
| |
Most Online9,918
Jul 28th, 2025
|
|
|
|
Joined: Dec 2008
Posts: 362 Likes: 7
Sidelock
|
Sidelock
Joined: Dec 2008
Posts: 362 Likes: 7 |
Raimey,
Photo # 9 on the Gun Auction listing for this one (see link on 1st page) clearly shows a nice radius where the action flats meet the standing breech.
Is that the radius you are referring to?
|
|
|
|
|
Joined: Aug 2007
Posts: 12,318 Likes: 459
Sidelock
|
|
Sidelock
Joined: Aug 2007
Posts: 12,318 Likes: 459 |
That's it. My curiosity is centered around did all Dalys have this feature.
Kind Regards,
Raimey
rse
|
|
|
|
|
Joined: Dec 2004
Posts: 110
Sidelock
|
|
Sidelock
Joined: Dec 2004
Posts: 110 |
Last edited by long range; 08/17/14 11:45 PM.
|
|
|
|
|
Joined: Dec 2004
Posts: 110
Sidelock
|
|
Sidelock
Joined: Dec 2004
Posts: 110 |
Last edited by long range; 08/17/14 10:54 PM.
|
|
|
|
|
Joined: Dec 2008
Posts: 362 Likes: 7
Sidelock
|
|
Sidelock
Joined: Dec 2008
Posts: 362 Likes: 7 |
David,
Love the old Leica rangefinder. A 3f?
Looks like you are well on your way with your Prussian Daly.
Battle was fortunate the screws on his are so nice, they look untouched.
|
|
|
|
|
Joined: Jun 2002
Posts: 2,347 Likes: 103
Sidelock
|
|
Sidelock
Joined: Jun 2002
Posts: 2,347 Likes: 103 |
Sounds like the metal will clean up nicely. How badly is the stock cracked under the leather patchwork? Butt transplants are not something I offer but if I was going to offer them structural integrity of the head of the stock would be critical. I try to council my clients to not spend "good money after bad" as my mother put it. I'm not trying to change your plans for the gun, just curious is all. Great project! I at first didnt see a crack towards the head. Further inspection i see a hair line carck rear of the repair. I'd guess they were able to close any crack up which now is invisible.
|
|
|
|
|
Joined: Jun 2002
Posts: 2,347 Likes: 103
Sidelock
|
|
Sidelock
Joined: Jun 2002
Posts: 2,347 Likes: 103 |
I'm collecting some info & was curious if any & all could provide the width of the water table/frame at the hinge pin & radius/standing breech as well as the length. Any effort would be greatly appreciated.
Kind Regards,
Raimey
rse Width at water table hinge pin 1.377 width across breech face 2.191 firing pin spacing is 1.055 not sure about radius.
|
|
|
|
|
Joined: Jun 2002
Posts: 2,347 Likes: 103
Sidelock
|
|
Sidelock
Joined: Jun 2002
Posts: 2,347 Likes: 103 |
How if any can i determine the manufactture?
|
|
|
|
|
Joined: Aug 2007
Posts: 12,318 Likes: 459
Sidelock
|
|
Sidelock
Joined: Aug 2007
Posts: 12,318 Likes: 459 |
With the S in a Chevron & the initials RS(if that is what is near the lower rib on the underside of the left tube) then the tubes were sourced from the Schilling forge and Robert Schlegelmilch was the tubeset knitter. I'd say the rest was performed inhouse by H.A. Lindner's mechanic pool.
No worries on the radius as it was just a point for measurement. How long was the water table/action flats?
Kind Regards,
Raimey
rse
|
|
|
|
|
|
|
