doublegunshop.com - home Forums General Discussion DoubleGun BBS @ doublegunshop.com suggestions for fixing a forend loop?

September
S	M	T	W	T	F	S
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30

Who's Online Now

5 members (Parabola, SKB, FallCreekFan, 2 invisible), 476 guests, and 2 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums10

Topics38,935

Posts550,898

Members14,460

Most Online1,344
Apr 29th, 2024

Print Thread

Re: suggestions for fixing a forend loop? Chuck H #44547 06/19/07 05:29 PM
Joined: Jan 2002 Posts: 606 Oshawa, Ontario, Canada Ron Vella Sidelock
Ron Vella Sidelock Joined: Jan 2002 Posts: 606 Oshawa, Ontario, Canada	ChuckH is absolutely correct. HiForce solder flows at around 500 degrees Fahrenheit, considerably above the flow temp of the 60/40 lead/tin solder used on these old guns. There's really no need to use anything but 60/40 if all surfaces are scrupulously clean and properly fluxed. Last edited by Ron Vella; 06/19/07 05:30 PM.

Entire Thread
Subject	Posted By	Posted
suggestions for fixing a forend loop?	John O-O	06/19/07 01:45 PM
Re: suggestions for fixing a forend loop?	bill schodlatz	06/19/07 02:56 PM
Re: suggestions for fixing a forend loop?	Robert Chambers	06/19/07 03:07 PM
Re: suggestions for fixing a forend loop?	775	06/19/07 04:24 PM
Re: suggestions for fixing a forend loop?	2-piper	06/19/07 04:59 PM
Re: suggestions for fixing a forend loop?	Chuck H	06/19/07 05:42 PM
Re: suggestions for fixing a forend loop?	Ron Vella	06/19/07 09:29 PM
Re: suggestions for fixing a forend loop?	Robert Chambers	06/19/07 09:58 PM
Re: suggestions for fixing a forend loop?	rabbit	06/19/07 10:20 PM
Re: suggestions for fixing a forend loop?	HomelessjOe	06/19/07 10:34 PM
Re: suggestions for fixing a forend loop?	eightbore	06/20/07 12:04 AM
Re: suggestions for fixing a forend loop?	Chuck H	06/20/07 01:40 PM
Re: suggestions for fixing a forend loop?	Fred	06/20/07 02:40 PM
Re: suggestions for fixing a forend loop?	Chuck H	06/20/07 03:58 PM
Re: suggestions for fixing a forend loop?	Fred	06/21/07 12:24 AM
Re: suggestions for fixing a forend loop?	Chuck H	06/19/07 10:38 PM
Re: suggestions for fixing a forend loop?	John O-O	06/20/07 12:04 PM

Link Copied to Clipboard

Updated every minute of everyday!

Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 0.354s Queries: 17 (0.335s) Memory: 0.8262 MB (Peak: 1.8992 MB) Data Comp: Off Server Time: 2024-09-28 13:40:34 UTC
Valid HTML 5 and Valid CSS