|
S |
M |
T |
W |
T |
F |
S |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
|
Forums10
Topics38,924
Posts550,761
Members14,459
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Dec 2003
Posts: 189
Member
|
Member
Joined: Dec 2003
Posts: 189 |
I have been under the impression that the monobloc does not allow the barrels to be set as close together as the other methods. I don't care for the seam and tend to favour a well made dove tail over the mono bloc.
But I'm a bit fuzzy on what a shoe lump is.
|
|
|
|
Joined: Jan 2006
Posts: 15,457 Likes: 88
Sidelock
|
Sidelock
Joined: Jan 2006
Posts: 15,457 Likes: 88 |
Are the ribs harder to relay on a chopper lump barrel ?
|
|
|
|
Joined: Jan 2002
Posts: 5,954 Likes: 12
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 5,954 Likes: 12 |
A monoblock would need to place the barrels further apart only if it is a significantly weaker joint than a chopper. IMO, the two piece nature of the monoblock breech is equivalent of the single piece nature of the chopper; it does not need to be thicker to compensate for weakness in the joint.
A "shoe" is any of a number of plate designs that cradle the barrel breeches and and join them vis soldering/brazing. The shoe also contains the hook and lumps. Look at the drawing on Hollowell's.
|
|
|
|
Joined: Jul 2006
Posts: 37
Junior Member
|
OP
Junior Member
Joined: Jul 2006
Posts: 37 |
I guess I am a little confused about the monoblock.
My impression is that the monoblock is a one piece affair into which the locking recesses, the hinge radius and the extractor cuts are make and into which two holes are bored to secure the barrels which are (I assume) silver soldered into place.
Am I right about that? Please?
RedHawk
|
|
|
|
Joined: Jan 2002
Posts: 5,954 Likes: 12
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 5,954 Likes: 12 |
rh44 - yep, you got that right. The reasons to set barrels further apart are to allow thicker breech walls or to fit to existing firing pin spacing. Per my concept that monoblocking doesn't require additional barrel spacing width, the practice of sleeving is little more than monoblocking the barrel set. It is practiced on all methods of barrel joining that I'm aware of and without any need to adjust barrel width.
When a barrel set is prepared for sleeving, the tubes are cut off and the breech end of the set reamed to accept a new tubes with the breech end sufficiently thick for chambering. The tubes can be glued in, soldered in, brazed in or welded in.
|
|
|
|
Joined: Jan 2002
Posts: 16
Junior Member
|
Junior Member
Joined: Jan 2002
Posts: 16 |
Is the monoblock considered down scale in terms of producing a quality O/U? No. Most quality O/U's (and not so quality O/U) use monobloc construction. I'd be more concerned with the method of barrel construction and machining if the barrels have choke tubes. I've don't remember an incident being reported of a monobloc joint failing, but choke-tube/barrel failures are common.
|
|
|
|
Joined: Jan 2002
Posts: 2,522
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 2,522 |
Possibly Unspellable might be visualizing a requirement to have a thicker piece of web between the barrels which isn't the case at all. The barrel stubs inserted into the monoblock can be a bit smaller outside diameter to accommodate web thickness if required for some specific reason. The Monoblock itself provides pressure containing strength.
|
|
|
|
Joined: Feb 2004
Posts: 13,880 Likes: 16
Sidelock
|
Sidelock
Joined: Feb 2004
Posts: 13,880 Likes: 16 |
Like most other things on guns, the quality of the design details and execution of them is more important than the design type.
I do recall something about a O/U gun, with monoblock construction, having a tube come out due to a bad solder joint. I think it was a newer Browning. I believe old Citori's were brazed or dovetailed barrels, breach to muzzle. The new 525 I have is monoblocked. I assume all the Citori line has gone this way for economical reasons.
|
|
|
|
Joined: Jan 2002
Posts: 16
Junior Member
|
Junior Member
Joined: Jan 2002
Posts: 16 |
Interesting that Miroku made the earlier Citori with chopper lump barrels. The Superposed was barrels are chopper lump so I suppose the Citori replacement guns came with them to help ease the transistion to a Japanesse made gun.
The literature that came with my CD/Miroku O/U has statements about the unique Miroku monobloc.
|
|
|
|
Joined: Jul 2006
Posts: 37
Junior Member
|
OP
Junior Member
Joined: Jul 2006
Posts: 37 |
Thanks to all for your comments. It was enlightening indeed.....
Last edited by redhawk44; 06/28/07 03:33 PM.
RedHawk
|
|
|
|
|
|