S |
M |
T |
W |
T |
F |
S |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
|
Forums10
Topics38,934
Posts550,873
Members14,460
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Dec 2001
Posts: 2,961 Likes: 9
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 2,961 Likes: 9 |
I use .002 in Briley light weights for skeet. The patter is great at skeet range (22 yards), 30 inches and uniform and full! bill
|
|
|
|
Joined: Dec 2010
Posts: 695 Likes: 11
Sidelock
|
Sidelock
Joined: Dec 2010
Posts: 695 Likes: 11 |
My Dickinson Estate .410 has factory marked M/M fixed chokes that measure .009/.009 with a dial caliper.
Wild Skies Since 1951
|
|
|
|
Joined: Feb 2004
Posts: 13,880 Likes: 16
Sidelock
|
Sidelock
Joined: Feb 2004
Posts: 13,880 Likes: 16 |
Interpretations of .410 full choke constriction seem to vary widely. Winchester had .017 in my M42s. My Ithaca ICD has .020. My Ugartechea had .025. A friend's 2 Perazzi guns had .036-.037.
I have a gun a previous owner opened the chokes to .000 and .010. I shot a lot of birds out pretty far with that cylinder bore. I believe the fact that I have very long forcing cones in that gun contributes greatly to the tight patterns.
|
|
|
|
Joined: Dec 2001
Posts: 2,961 Likes: 9
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 2,961 Likes: 9 |
Less choke = better patterns. The less crush inflicted on the shot string the fewer flyers, we polished forceing cones on 410 tubes and increased the BB count in a 30 inch circle by 25 and the percent by 15%
bill
|
|
|
|
Joined: Jan 2002
Posts: 13,386 Likes: 1324
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 13,386 Likes: 1324 |
My Dickinson Estate .410 has factory marked M/M fixed chokes that measure .009/.009 with a dial caliper. Where on the gun are they marked, WS? I've never seen choke markings on mine. SRH
May God bless America and those who defend her.
|
|
|
|
Joined: Dec 2007
Posts: 1,174
Sidelock
|
Sidelock
Joined: Dec 2007
Posts: 1,174 |
Stan mine is fixed mod/mod as indicated by the 3 stars on each barrel forward of the flats. Works well for me. Adam
|
|
|
|
Joined: Jan 2002
Posts: 13,386 Likes: 1324
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 13,386 Likes: 1324 |
Hi Adam,
I was wondering where you had been. Thanks, I hadn't read the manual and had not noticed the stars. I'll see what mine has, but I'll bet it's got three stars, too.
SRH
May God bless America and those who defend her.
|
|
|
|
Joined: Jan 2002
Posts: 13,386 Likes: 1324
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 13,386 Likes: 1324 |
Chuck and Bill,
I have two guns on which I'd like to lengthen the cones and polish them, but they are both chrome lined, and I just hate messing with them. Have either of you ever cut any that were chrome lined?
SRH
May God bless America and those who defend her.
|
|
|
|
Joined: Feb 2004
Posts: 13,880 Likes: 16
Sidelock
|
Sidelock
Joined: Feb 2004
Posts: 13,880 Likes: 16 |
Stan, I have not. But a high speed steel reamer will get trashed cutting it. A sharp HSS reamer that has been TiN coated should cut it. TiN is harder than chrome. My 3" forcing cone reamer is simply a regular #8, 1/4" per ft taper pin reamer, with the forward chamber diameter O.D. ground (no clearance) on it. Something like this. https://www.mscdirect.com/product/details/02402089 A custom cutter grinder should have a source ti TiN coat. Carbide would just be expensive as hell.
Last edited by Chuck H; 08/24/16 07:19 AM.
|
|
|
|
Joined: Jan 2002
Posts: 13,386 Likes: 1324
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 13,386 Likes: 1324 |
Chuck,
I just emailed Mike Orlen with that question. I will post his reply when I receive it.
Thanks, SRH
May God bless America and those who defend her.
|
|
|
|
|