S |
M |
T |
W |
T |
F |
S |
|
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
|
|
1 members (btbell),
305
guests, and
5
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,615
Posts547,014
Members14,427
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Jan 2002
Posts: 9,795 Likes: 773
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 9,795 Likes: 773 |
They do not.
That said, I am always very hesitant to bend a stock that is difficult to replace. A Charlin is right there with a Darne, in that regard.
Best, Ted Thanks. Sorry to hear that Charlins are tough to restock, too. I know of one that needs new wood. It is a sad truth that almost everyone knows of one or two that need new wood. A Darne is not a hard gun to stock, or, restock, if you know what you are doing. The hard part is drilling the big hole that takes the big wood screw that retains the stock. At the factory, the guys had a rack of turned blanks, the heading up was mostly done, ready to go into the lathe that was fixtured to drill the hole. My gun got a raw blank, but was stocked and ready to checker in a few hours. If I was looking for a winter project, Id look for a Charlin before a Darne. But, either gun is a bit above what I think an amateur project would be. Best, Ted
|
|
|
|
Joined: Dec 2006
Posts: 1,521 Likes: 20
Sidelock
|
Sidelock
Joined: Dec 2006
Posts: 1,521 Likes: 20 |
Ted: How well do Charlins compare with Darnes? There is a 16 gauge that appeared for sale recently on Gunsinternational.com that I'm considering. It's clearly refinished and reblued by some means other than rust bluing. https://www.gunsinternational.com/guns-f...un_id=101554342I'm only interested because it's a 16 gauge, has reasonable stock dimensions and would go well with my 10 and 12 gauge Darnes. Thanks. Rem
|
|
|
|
Joined: Jan 2002
Posts: 998 Likes: 9
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 998 Likes: 9 |
Do not see a safety in the GI pix of that Charlin, Rem???? Also note that it has 2-1/2 inch chambers (65mm).
Regards, Tim
Last edited by Tim Carney; 11/25/20 01:39 PM.
|
|
|
|
Joined: Jan 2002
Posts: 9,795 Likes: 773
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 9,795 Likes: 773 |
I wouldnt buy that gun.
To your question, a Charlin is not a Darne. When they have a safety lever, that safety has a very stout little leaf spring, that makes the safety a bear to get on and off. It sounds like a minor point, but, I got rid of my Charlins over that minor point. This one is missing its safety lever. Not good. You may see some internet prattle about how superior a Charlin is to a Darne, how smooth and refined the action is, and whatnot. Is is BS, usually prattled by someone who has a Charlin to sell. The smoothness is only a factor when the gun is cocked, and you are cycling the action for fun. When it is time to cock either gun, they take the same amount of effort, and make the same amount of noise. There is an interrupter in the opening key of a Charlin that keeps the gun from firing if it isnt all the way closed. Good idea, but, the bolts that hold a Darne closed are already engaged before the gun can be fired. A Charlin has no bolts, it is purely an over-the-center device. If you use ammunition that is a bit too long in a short chamber Charlin, the gun will often reward you with torn off ends on the spent cases, savage recoil (same as any other light gun with the wrong ammunition) and an opening lever slightly out of battery. It cant open at the shot (over the center device) but, that fact alone doesnt keep guys from wetting themselves when they see it. Use the right ammunition, and it isnt a thing.
They are similar, but, different designs, and one really has to discover which he prefers, by using both. Some guys love em, some guys (me) sold their Charlins and stuck with a Darne.
Best, Ted
|
|
|
|
Joined: Dec 2006
Posts: 1,521 Likes: 20
Sidelock
|
Sidelock
Joined: Dec 2006
Posts: 1,521 Likes: 20 |
Tim and Ted:
Thank you. I'll keep looking.
Rem
|
|
|
|
|