doublegunshop.com - home Forums General Discussion DIY Gunsmithing @ doublegunshop.com Removing broken pin from drilling sidelock plate

December
S	M	T	W	T	F	S
	1	2	3	4	5	6
7	8	9	10	11	12	13
14	15	16	17	18	19	20
21	22	23	24	25	26	27
28	29	30	31

Who's Online Now

5 members (Jolly Bill, LGF, Researcher, Mike Harrell, AaronN), 1,371 guests, and 7 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums10

Topics39,639

Posts563,660

Members14,602

Most Online9,918
Jul 28th, 2025

Print Thread

Re: Removing broken pin from drilling sidelock plate pomofo #587158 12/14/20 05:17 AM
Joined: Dec 2001 Posts: 7,340 Likes: 661 Colorado SKB Sidelock
SKB Sidelock Joined: Dec 2001 Posts: 7,340 Likes: 661 Colorado	I would clamp it to a piece of flat stock, put the stock in a vise, center drill the old screw are carefully drill out the old screw. It is a through hole and should be pretty easy to do. I have done lots of them this way, much harder in a blind hole. Last edited by SKB; 12/14/20 05:31 AM. Firearms imports, consignments

Entire Thread
Subject	Posted By	Posted
Removing broken pin from drilling sidelock plate	pomofo	12/14/20 04:22 AM
Re: Removing broken pin from drilling sidelock plate	SKB	12/14/20 10:17 AM
Re: Removing broken pin from drilling sidelock plate	Der Ami	12/14/20 03:20 PM
Re: Removing broken pin from drilling sidelock plate	keith	12/14/20 06:45 PM
Re: Removing broken pin from drilling sidelock plate	Mark II	12/14/20 04:52 PM
Re: Removing broken pin from drilling sidelock plate	damascus	12/14/20 08:33 PM
Re: Removing broken pin from drilling sidelock plate	Der Ami	12/14/20 11:58 PM
Re: Removing broken pin from drilling sidelock plate	bavarianbrit	01/14/21 05:08 PM
Re: Removing broken pin from drilling sidelock plate	pomofo	12/16/20 02:44 AM
Re: Removing broken pin from drilling sidelock plate	David Williamson	12/16/20 01:13 PM
Re: Removing broken pin from drilling sidelock plate	Shotgunlover	01/13/21 10:07 AM

Link Copied to Clipboard

Updated every minute of everyday!

Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 0.450s Queries: 17 (0.374s) Memory: 0.8117 MB (Peak: 1.9025 MB) Data Comp: Off Server Time: 2025-12-01 03:33:53 UTC
Valid HTML 5 and Valid CSS