doublegunshop.com - home Forums General Discussion DIY Gunsmithing @ doublegunshop.com MWT at forcing cone - 16ga and 20ga

All true Daryll, I was responding to the attack by the troll on Mark, not on MG's comment regarding wall thickness or the troll's response to it.

Just my 12$ on the subject

SKB, I misunderstood, but it is good that I did, as Mr. Griffin's information is dangerously wrong.

Daryl, sometimes it isn't about staying on-topic and correcting information that is not just wrong, but actually dangerous.

That's why I felt that if Mark can make the effort to post a Free Advertising Tagline link to his business, he could have at least shared his chart of CIP recommended barrel wall thickness for the benefit of everyone who visits this information sharing forum.

And especially if he hasn't been paying Dave the $12.00 fee for each and every sale resulting from many years of Free Advertising.... just like you know who....

But some people just feel entitled and special, and think everyone else should subsidize their business ventures. And protecting that self interest is obviously more important than a shotgun blowing up in someone's face.

I think it is a matter of perspective Karen. I mean, some people make an effort to criticize the work of others while never once in more than a dozen years bother to post a picture of their own work, quite hypocritical in my mind. I believe this usually happens when someone lacks experience and is bitter over that fact.

Just my 12$ on the subject.

By the way, your mailbox is full

All my best,
Steve

I believe I have posted a couple pics of my work in the past Princess Stevie. So sorry you missed them. Go back and look through my old posts.

I also recall that you have been rudely critical of some work posted by others, so it further illustrates your sense of entitlement to feel your work should only get fawning praise. Not my fault you don't have the talent Dewey Vicknair, CJO, and others have..

I recall jOe posted pics of the first leather covered pad he did. It wasn't bad for a first try, but the leather he used was a bit too thick, and he didn't cut the pad down enough to accommodate the thickness. Naturally, it was a bit proud if the stock. Others said he did well, and some offered suggestions and encouragement. But not you Princess Hypocrite. You insulted him and his work. You mocked him afterwards.

More recently, Kolar posted pics of a couple trap gunstocks he made. Again, you were very critical. You said they had the refinement of a canoe paddle.

Is this ringing any bells in your thick crybaby head Princess? So why are you immune from criticism?

But I'll tell you what... I'll post a couple pictures of some of my work. I'll fully expect you to inspect for the slightest faults, and to be the usual turd you are. That's OK

However, I'm not just going to immediately satisfy your request when you have been running away from my request for years now. So if you want pics, then quit being a coward and tell us whether you are paying Dave the $12.00 fee for each and every sale resulting from your Free Tagline Advertising. Tell us about all the times you advertised in the For Sale Forum, and then announced the item was sold on another website, so you could skate free. Then I will grant your photo request Princess.

And tell all of the people you are bullshitting how you filled my PM box with vulgar PM's. Let them know what a self-centered and entitled POS you really are.

Poor little Princess. I answered your question on the 12$ multiple times and will not again. I have told you that before sweetheart.

Speaking of bIg dAddy frAnk, how goes the relationship? I haven't heard much from him lately. Are you two still a thing?

Honey, you are the self-centered POS on this board, you are nothing but a petty little troll who lacks experience. I will point out that it is you who has decided to make this forum your own personal platform for airing your grievances.

Your multiple ongoing feuds on this board speak to just how small of a person that you are.

You could prove me wrong, but you won't.

All my best,
Steve

P.S. Your mail box is full