|
S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums10
Topics40,431
Posts575,369
Members14,712
| |
Most Online32,084
Jun 14th, 2026
|
|
|
|
Joined: Aug 2007
Posts: 12,959 Likes: 560
Sidelock
|
Sidelock
Joined: Aug 2007
Posts: 12,959 Likes: 560 |
![[Linked Image from i.imgur.com]](https://i.imgur.com/1rILlUN.jpeg) ![[Linked Image from i.imgur.com]](https://i.imgur.com/KWMwP47.jpeg) It appears there is a screw hole under that bar you mentioned? Serbus, Raimey rse
|
|
|
|
|
Joined: Dec 2001
Posts: 3,626 Likes: 21
Sidelock
|
|
OP
Sidelock
Joined: Dec 2001
Posts: 3,626 Likes: 21 |
That screw may hold the trigger group to the lower plate?
Serbus,
Raimey
rse Saw that. Not directly in line, but if it ends anywhere(on the exterior), it is just ahead of the word "SAFE" ![[Linked Image from i.postimg.cc]](https://i.postimg.cc/wyP554wq/20260904-112210-1.jpg)
Last edited by Utah Shotgunner; 09/04/26 02:22 PM.
Mike
|
|
|
|
|
Joined: Aug 2007
Posts: 12,959 Likes: 560
Sidelock
|
|
Sidelock
Joined: Aug 2007
Posts: 12,959 Likes: 560 |
![[Linked Image from i.imgur.com]](https://i.imgur.com/5Qq6MxM.jpeg) Good Eye & that's the culprit. Serbus, Raimey rse
|
|
|
|
|
Joined: Dec 2001
Posts: 3,626 Likes: 21
Sidelock
|
|
OP
Sidelock
Joined: Dec 2001
Posts: 3,626 Likes: 21 |
It appears there is a screw hole under that bar you mentioned?
Serbus,
Raimey
rse The sliding top bolt is connected internally to the double underbolts with no obvious way to separate. IF there is a screw, not getting to it with the bolt in place. I'm looking for this piece of advice that says "Remove X to get to screw"
Last edited by Utah Shotgunner; 09/04/26 02:25 PM.
Mike
|
|
|
|
|
Joined: Dec 2001
Posts: 3,626 Likes: 21
Sidelock
|
|
OP
Sidelock
Joined: Dec 2001
Posts: 3,626 Likes: 21 |
Good Eye & that's the culprit.
Serbus,
Raimey
rse I am not convinced. IF it is the other end of the screw, this action was assembled to never be taken apart.
Mike
|
|
|
|
|
Joined: Aug 2007
Posts: 12,959 Likes: 560
Sidelock
|
|
Sidelock
Joined: Aug 2007
Posts: 12,959 Likes: 560 |
You may be right as that screw that lands up @ >>SAFE<< could be under the triggerplate?
Serbus,
Raimey
rse
|
|
|
|
|
Joined: Dec 2001
Posts: 3,626 Likes: 21
Sidelock
|
|
OP
Sidelock
Joined: Dec 2001
Posts: 3,626 Likes: 21 |
You may be right as that screw that lands up @ >>SAFE<< could be under the triggerplate?
Serbus,
Raimey
rse The two location are not in line. Bottom is approx. 1/8" forward of the "SAFE". Still tinkering.
Mike
|
|
|
|
|
Joined: May 2008
Posts: 1,150 Likes: 474
Sidelock
|
|
Sidelock
Joined: May 2008
Posts: 1,150 Likes: 474 |
Why do you not do as SKB stated?
|
|
|
|
|
Joined: Dec 2001
Posts: 7,745 Likes: 920
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 7,745 Likes: 920 |
![[Linked Image from i.imgur.com]](https://i.imgur.com/wpUD8BLl.jpg) This is mine, you slide the top bolt out to the rear, under it is the top tang pin. The top lever screws into a yoke that engages with the double under bite bolt.
|
|
|
|
|
Joined: Feb 2002
Posts: 1,976 Likes: 291
Sidelock
|
|
Sidelock
Joined: Feb 2002
Posts: 1,976 Likes: 291 |
The small screw end showing behind the triggers is likely the Trigger tension spring attachment.
The small screw end showing above the 'SAFE' marking is probably part of the safety assembly inside.
** note that the SAFE marking is engraved/inlayed onto a separate small plate that is dovetailed into the top tang all the way across the tang.
The screw end intersects that dovetail, very slightly.
If you get to the point where that screw needs to be removed,,the dovetailed plate w/SAFE on it should be removed first.
Otherwise turning that screw out may damage that plate, the dovetail being part of it.
|
|
|
|
|
![[Linked Image from i.imgur.com]](https://i.imgur.com/NrDaZrQl.jpg)