doublegunshop.com - home
Posted By: tunes 9.3x72r reloading components for sale - 05/04/21 06:30 PM
Brass
39 Norma new
5 S&B once fired

Cast bullets-
50-- 200gr Round Nose .365dia
50-- 195gr Flat Nose .366dia
25-- 250gr Flat Nose .366dia

Mould for the 195gr .366dia cast bullets

Jacketed Bullets
87-- Hawk 200gr Round Nose .030 jacket .365dia
28 --Buffalo Arms 193gr Flat Nose .366dia

Would prefer to sell as one lot--

$160.00 shipped in the USA

[Linked Image from i.imgur.com]

[Linked Image from i.imgur.com]

[Linked Image from i.imgur.com]

[Linked Image from i.imgur.com]
Posted By: Hoot4570 Re: 9.3x72r reloading components for sale - 05/04/21 08:33 PM
Sir, I will take this. PM to follow.
Posted By: tunes Re: 9.3x72r reloading components for sale - 05/04/21 09:38 PM
SOLD to Hoot, thank you

PM sent
Posted By: 67galaxie Re: 9.3x72r reloading components for sale - 05/05/21 12:55 AM
Too cool! Can you tell me were you got your supplies from and message me any loads you liked?
Posted By: 9372 Re: 9.3x72r reloading components for sale - 09/27/21 10:47 AM
Hello! Im looking for old vintage reloading tools for 9,3x72r, to start reload for my old Suhl drilling. Anyone can help me with sources of such a antique equipment please? Thank you.
Posted By: Der Ami Re: 9.3x72r reloading components for sale - 09/27/21 02:06 PM
9372,
Antique reloading tools will be hard to find and will likely take time, unless you are willing to to spend more than they are worth. However you can load perfectly useable ammo and enjoy your drilling while searching. The first step is to "slug" your barrel, they vary wildly in groove diameter( from about .358" to .368") and you might be able to use commonly available bullets. When I started loading the 9.3x72, I used my 9.3x74R dies as "neck sizing" dies, with the expander removed, and expanded / deprimed by hand with shop made expander made to fit a .364" bullet. I know it's hard to believe, but not everyone has 9.3x74R dies. With careful adjustment and a shellholder that fits, you can likely use 35 Rem./ 358 Win./35 Wh. modern dies. This would allow you time for your search.
Mike
Posted By: 9372 Re: 9.3x72r reloading components for sale - 11/06/21 01:14 AM
Hi! Thank you, I slugged the bore, and made a cast. Bore is 9,30-9,34mm, chamber is slightly larger, rim - 12,5mm,base-11mm, I think is 9.3x72r-D. I am waiting for die sets but it can take few months.I got 13,2g. 366 round nose bullets and old type 72U 14,9g flat nose . 364 with .375 driving band/stopping ring. I was thinking to load 14,9g bullets with black powder. I do have challenger press, factory crimping dies, many load data. If you have any sugestions, information, please let mé know. Ánd once more Thank you.
Posted By: Der Ami Re: 9.3x72r reloading components for sale - 11/09/21 07:07 PM
9372,
I can't help you much with your plan to use black powder, as I don't use it in my German rifles, but I'm sure others here can help. It seems you are a little concerned that your chamber is a little larger. This is very common and results from comparing the diameter of a cartridge base with the diameter of the chamber at the same location. A chamber must be larger than the cartridge, otherwise it will not enter. How much larger varies between makers and it seems older chambers are often larger than newer ones. Your chamber does not seem to be unusually large and I would not be concerned about it. It seems that you have done your research and have the project pretty much "in hand".
Mike
Posted By: oskar Re: 9.3x72r reloading components for sale - 11/10/21 07:02 PM
My bore mics .364 and .344, very tall skinny lands. I use Buffalo Arms bullets that are a two step bullet same as factory S&B ammo. I have a .358 200gr bullet mold that I'm going to paper patch up to .364 and try that. I have patch patterns cut and have patched a couple but haven't fired them yet.

I would have bought the components to just to get the molds.
© The DoubleGun BBS @ doublegunshop.com