|
S |
M |
T |
W |
T |
F |
S |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
|
1 members (J.B.Patton),
410
guests, and
1
robot. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,900
Posts550,591
Members14,458
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Jan 2013
Posts: 9
Boxlock
|
OP
Boxlock
Joined: Jan 2013
Posts: 9 |
I found my way here while searching for Newton information. I'm not a collector, but I have two first model Newtons, a .256 that I just recently bought and a .30 Newton that has been in my family since my Great-Grandfather bought it. I've never shot either of them, but I am planning to do so. I've purchased 100 pieces of brass for each from Jamison's and Quality Cartridge and have die sets for them, RCBS dies for the .30 and CH dies for the .256. The .256 is going to be my deer rifle and I hope to one day hunt moose with the .30. I am planning on shooting either 125 gr. Partitions or 130 gr. Accubonds in the .256 and something similar in 180 gr. for the .30. I've probably found all of the available loading data for both, but if anyone has a load that has worked well for them, I would appreciate any info you would be willing to share as a place to start. An Uncle of mine has another .30 Newton that he picked up long ago as a rehab project that he hasn't gotten around to doing. As I recall, it's missing the buttplate, the front sight has been changed and whoever had it before him botched a bedding job and left it a mess. I'm thinking that I should take it off his hands and attempt to resurrect it. Anyone know where a Newton buttplate might be found? Or how to remove bedding compound without destroying whats left of the finish? Rob
Last edited by RememberBaker; 01/07/13 10:34 AM. Reason: Poor grammar
|
|
|
|
Joined: Dec 2001
Posts: 6,881
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 6,881 |
Welcome to the forum.
I am not very knowledgeable about Newtons but there are a couple folks who are and stop by now and then.
MP Sadly Deceased as of 2/17/2014
|
|
|
|
Joined: Mar 2009
Posts: 25
Boxlock
|
Boxlock
Joined: Mar 2009
Posts: 25 |
Newton parts are hard to come by and the major firearms gun sites are the best places to monitor for any for sale. I have not done too much reloading for Newtons and hopefully the guy who I rely on for info will stop by and enlighten you. My listed favorite loads for the 256 (a First Model 1916) are 53.6 grains of RL22 with a 120 grain Nosler Ballistic tip or a 125 grain Nosler Partition. I have tried to use 140 grain bullets with average sucess. The rifling in the 1916 is suited to the lighter bullets and the Second Model 1924 has rifling more suited to the 140 grain bullets. Larry wales
LSW
|
|
|
|
Joined: Nov 2008
Posts: 86
Sidelock
|
Sidelock
Joined: Nov 2008
Posts: 86 |
At one time I had twenty nine 256 Newtons but only shot a few of them. There was a restocked one that I hunted with and shot deer, antelope and black bear with it. 48-51 grains of IMR 4350 is what I used. At the upper end, some guns showed signs of high pressures, so be careful.
|
|
|
|
Joined: May 2011
Posts: 744
Sidelock
|
Sidelock
Joined: May 2011
Posts: 744 |
vinegar might budge the bedding compound, but it might also affect the blueing...
|
|
|
|
Joined: Jan 2004
Posts: 6,988 Likes: 491
Sidelock
|
Sidelock
Joined: Jan 2004
Posts: 6,988 Likes: 491 |
Vinegar WILL affect the bluing. For sure.
_________ BrentD, (Professor - just for Stan) =>/
|
|
|
|
Joined: Jan 2013
Posts: 9
Boxlock
|
OP
Boxlock
Joined: Jan 2013
Posts: 9 |
Thank you kindly for the responses thus far, more would be welcome as well.
Anyone with experience loading for a .30 Newton?
The bedding compound on the other .30 That I mentioned isn't on metal, it ran out onto the exterior of the stock and was left there. I haven't seen the rifle in years and I can't remember just how much of it there was.
|
|
|
|
Joined: Mar 2009
Posts: 25
Boxlock
|
Boxlock
Joined: Mar 2009
Posts: 25 |
Another point to remember if you plan on shooting an original Newton rifle is the potential weakness of the stocks. Some of the 256s and about half of the 30s and 35s have cracked stocks in the Model 1916 and more in the 1924. These cracks are not always easy to detect. The rifle has to be taken down and carefully inspected behind the magazine and in front of and behind the trigger area. Many times the cracks will only be "hairline" cracks. Obviously, if undetected, they are potential for stock failure especially in the higher calibers. Be careful. Newton rifles without cracks in the stocks are sometimes hard to find and will bring a higher value. If I have someone contact me with an original without a crack in the stock and they want to shoot it, I recommend they obtain an extra stock and use it to shoot the rifle. Again, especially in the 30 and 35 Newton. Larry Wales
LSW
|
|
|
|
Joined: Apr 2006
Posts: 641 Likes: 2
Sidelock
|
Sidelock
Joined: Apr 2006
Posts: 641 Likes: 2 |
If I have someone contact me with an original without a crack in the stock and they want to shoot it, I recommend they obtain an extra stock and use it to shoot the rifle. Again, especially in the 30 and 35 Newton. Larry Wales Larry, My .30 Newton already has such a crack, and I have a .256 with a horrible "custom" stock I would like to replace with an original, or barring that, a clone of an original. Do you have a source for such stocks? Bill Warren
|
|
|
|
Joined: Sep 2008
Posts: 907
Sidelock
|
Sidelock
Joined: Sep 2008
Posts: 907 |
Bill I have a original that just needs a little bondo on the heel toe etc to get it ready for a pattern and I also have a un-inletted clone copy. I would be glad to loan you either. The problem is I will be in the hospital for a while and not in commission for a while.And not able to ship right now. But if interested let me know. And when I can would be glad to send you either for you to get a copy made. Whitey
Last edited by whitey; 01/08/13 08:16 PM.
|
|
|
|
|
|