|
S |
M |
T |
W |
T |
F |
S |
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
1 members (smlekid),
1,150
guests, and
6
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,445
Posts544,841
Members14,406
|
Most Online1,258 Mar 29th, 2024
|
|
|
Joined: Jan 2005
Posts: 87
Sidelock
|
OP
Sidelock
Joined: Jan 2005
Posts: 87 |
Have a Woodward 12g. side lever.# 3870. Whitworth barrels badly pitted on the outside. Bores nice. any suggestions on a fix? Thank you
|
|
|
|
Joined: Feb 2011
Posts: 355 Likes: 50
Sidelock
|
Sidelock
Joined: Feb 2011
Posts: 355 Likes: 50 |
|
|
|
|
Joined: Mar 2002
Posts: 7,710 Likes: 474
Sidelock
|
Sidelock
Joined: Mar 2002
Posts: 7,710 Likes: 474 |
If really deep pits your options are three. One have a new set of barrels made at very high cost. Two have it sleeved at moderate cost but risk major balance changes. Or three put brileys subgauge tubes put in it and shoot a heavy fence post. I guess your fourth option would be do nothing. I feel your pain.
Personally I’d send it back to GB and have the best sleeve job available done. The best get the weight close to original and are seamless. Cheap sleeve jobs are like poor circumcisions. Just hard to even look, at much less call our own. JMO.
|
|
|
|
Joined: Nov 2006
Posts: 1,625 Likes: 73
Sidelock
|
Sidelock
Joined: Nov 2006
Posts: 1,625 Likes: 73 |
Send it to Purdey to be re-barreled.
Mike Proctor
|
1 member likes this:
67galaxie |
|
|
|
Joined: Mar 2002
Posts: 2,857 Likes: 384
Sidelock
|
Sidelock
Joined: Mar 2002
Posts: 2,857 Likes: 384 |
And palunc will gladly pay for it
|
1 member likes this:
67galaxie |
|
|
|
Joined: Mar 2002
Posts: 2,857 Likes: 384
Sidelock
|
Sidelock
Joined: Mar 2002
Posts: 2,857 Likes: 384 |
|
|
|
|
Joined: Dec 2001
Posts: 6,266 Likes: 199
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 6,266 Likes: 199 |
I have had pits on the exterior of Damascus barrels cleaned and welded. Even on these Damascus barrels, after refinishing, the pit repair was not obvious. The gun in question apparently has Whitworth Fluid Steel barrels. That should be an easy fix and not visable after a good rust blue .
|
1 member likes this:
mc |
|
|
|
Joined: Jan 2009
Posts: 767 Likes: 19
Sidelock
|
Sidelock
Joined: Jan 2009
Posts: 767 Likes: 19 |
There are several very good micro welders and Iike several above I have had good, not excellent, results. Some can match the modern steel rods to Whitworth fluid steel but some can not. There is a “restorative” MW, Peter something in IL that has posted his work. Worth a look and phone call.
Good luck. Woodward’s are nice guns.
|
|
|
|
Joined: Dec 2001
Posts: 6,991 Likes: 402
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 6,991 Likes: 402 |
I have worked with Peter Nagel at restorative welder extensively in the past, he is a superb TIG welder and extremely knowledgeable about metallurgy. Peter is not a micro-welder though. You might look on the ACGG website at the metalsmith category. I have a micro-welder myself but am not taking any new work at the moment until I catch up with my current workload. Good luck and if you are able, please post some pictures.
|
|
|
|
Joined: Jan 2006
Posts: 9,412 Likes: 313
Sidelock
|
Sidelock
Joined: Jan 2006
Posts: 9,412 Likes: 313 |
My apologies for noting the obvious, but "nice bores" in a vintage gun usually means honing. If the wall thickness is inadequate, your options are limited. Please share the end-of-chamber, 9", mid-barrel, and MWT (and location thereof). Bertram Edmonston is another option https://www.facebook.com/BertramCustom/photos/a.1406522922897924/2406368079580065/?type=3
|
|
|
|
|
|