|
S |
M |
T |
W |
T |
F |
S |
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums10
Topics38,465
Posts545,068
Members14,409
|
Most Online1,258 Mar 29th, 2024
|
|
|
Joined: Feb 2011
Posts: 356 Likes: 51
Sidelock
|
OP
Sidelock
Joined: Feb 2011
Posts: 356 Likes: 51 |
Hello. I have some 303 British and it is old Berdan, corrosive primed and it fires, delay fires, and won't fire so I am pulling the bullets and wanting to reload them using the cordite. Is it okay if some of the strands of Cordite break and is the wad necessary? Thank you.
|
|
|
|
Joined: Jul 2012
Posts: 4,463 Likes: 207
Sidelock
|
Sidelock
Joined: Jul 2012
Posts: 4,463 Likes: 207 |
liverwort, I wouldn't be as concerned about using the same cordite as I would the primers. I am not concerned about loading Berdan primers "per se" but the 303 British ammo may be loaded with varying diameter primers and may contain mercury in the priming compound. Primers being corrosive can be dealt with pretty handily, but mercuric primers destroy the cases for further use by embrittling them. I load several different calibers with Berdan primers but depend on an old stock of common diameters primers that I have been to find replacement for. My online searches for a replacement source have been unsuccessful, so far. If you have the correct diameter non-mercuric (and preferably non-corrosive) primers, you can reload the cartridges that didn't fire and any that you haven't tried, if you remove the original primers by safe means. The cases from the cartridges that did fire may or may not be useable. This sounds like something I would do but I believe using reasonably available modern cases would be much easier. It is my understanding that when cordite was used the cases were charged before "necking" the case down to the final diameter. As you have likely discovered, shaking the cordite strands out of the cases would be hard enough but putting them back in will require a lot of time and must be done "by hand". Unless you can salvage a lot of cordite, I believe it would be more economical to salvage the bullets by a collet type "puller" and forget about reusing the cordite. This would be true if you can find the correct Berdan primers or you use Boxer primed modern cases. I think the wad was used to "locate" the cordite strands during "necking" operation, rather than a filler. Any cases you would use would already be "necked" down. If you think a filler is required, that would be a decision no one but you should make. Mike
|
|
|
|
Joined: Feb 2011
Posts: 356 Likes: 51
Sidelock
|
OP
Sidelock
Joined: Feb 2011
Posts: 356 Likes: 51 |
Der Ami, Thank you for your reply. I think you are exactly right. The Berdan primers are unreliable to be used, and the brass, requiring those primers is useless to me as well. I was thinking that I would pull the Cordite and reload it into boxer primed cases and reload the bullets but I think you are again correct in that getting that cordite back in a new case would be as difficult as trying to deprime the original cases. I noticed also that the rounds I am unloading, have two different primer sizes. Any thoughts on a use for the cordite?
|
|
|
|
Joined: Jul 2012
Posts: 4,463 Likes: 207
Sidelock
|
Sidelock
Joined: Jul 2012
Posts: 4,463 Likes: 207 |
you can just scatter it in your wife's flower bed or into the lawn. it makes pretty good fertilizer with its nitrogen content. The main thing to remember is that you shouldn't make piles. Some people burn it, but it burns very hot and is dangerous, so this practice is to be avoided. Mike
|
|
|
|
Joined: Feb 2011
Posts: 356 Likes: 51
Sidelock
|
OP
Sidelock
Joined: Feb 2011
Posts: 356 Likes: 51 |
|
|
|
|
|
|