March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Who's Online Now
5 members (Marc Ret, SKB, Argo44, FlyChamps, 1 invisible), 370 guests, and 2 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums10
Topics38,374
Posts544,002
Members14,391
Most Online1,131
Jan 21st, 2024
Previous Thread
Next Thread
Print Thread
Joined: Dec 2001
Posts: 363
Likes: 16
Sidelock
***
OP Offline
Sidelock
***

Joined: Dec 2001
Posts: 363
Likes: 16
My question in what actual strength of ferric chloride solution are you using in Damascus finishing? 29% is a more or less standard solution strength, as called for in lots of rust bluing and Damascus finishing solutions. And people refer to that or milder solutions in Damascus finishing. But what is the strength of the commonly available Radio Shack solution? My bottle also lists hydrochloric acid as an ingredient.

If I take my 29% solution and cut it 1:1 with water, my result is 14.5%, if I cut it 1:1 again I get 7.25%. But I don't know what the strength of the Radio Shack solution is from the bottle.

I don't remember enough chemistry to remember if more that 29 Grams will dissolve in 61cc of water.


Dennis Potter
Joined: Mar 2013
Posts: 2,862
Sidelock
***
Offline
Sidelock
***

Joined: Mar 2013
Posts: 2,862
It's basically the same as yours. As I recall, it might be 31%, near enough to not really matter. I believe it does not contain HCL. The problem with HCL in etching solutions is it's prone to after-rusting relativly fast. But, it is one of the two acids in Aqua Regia type rusting solutions.

Regards
Ken

Last edited by Ken61; 01/02/17 10:38 PM.

I prefer wood to plastic, leather to nylon, waxed cotton to Gore-Tex, and split bamboo to graphite.
Joined: Feb 2002
Posts: 1,850
Likes: 150
Sidelock
***
Offline
Sidelock
***

Joined: Feb 2002
Posts: 1,850
Likes: 150
Here's the RadioShed MSDS for their etch.
https://cdn.shopify.com/s/files/1/0953/5...314291674007590

It shows the Ferric Chloride % at anywhere from 30% to 60% (??) ...unless I read it wrong! wouldn;t be the first time.
The hydrochloric acid content is 1/10% to 1.0%

Kind of hard with that wide range of 30 to 60% to dilute it to anything specific.

The stuff I use I bought off of EvilBay some years back. It;s marked as a specific % soln,,forget what it is.
I use it diluted to about 3 or 4% for damascus finishing

Joined: Mar 2002
Posts: 7,693
Likes: 450
Sidelock
**
Offline
Sidelock
**

Joined: Mar 2002
Posts: 7,693
Likes: 450
I have bought 42& ferric chloride off EBay. Then just diluted to what ever strength required. I admit I write it down on paper and use a calculator to get the amount to dilute it by correct. I tried Jethro Bodine math but got my ought(s) messed up and ended up with a much stronger mix than I wanted.

Joined: Feb 2004
Posts: 13,879
Likes: 15
Sidelock
***
Offline
Sidelock
***

Joined: Feb 2004
Posts: 13,879
Likes: 15
Dennis,
When I was experimenting with this, I had corresponded with Dr. Gaddy. What was unclear was the actual strength of the FeCl He gave me percentages, but I didn't know they were based on starting with a Radio Shack circuit board etch which is only 41% FeCl

So my experiments finally fleshed out that one part 41% strength circuit board etch diluted at least 6 parts water will work with a 10 second dip and immediate water flush with a wet carding of 000 or 0000 steel wool. 8 parts water will give you a little more time in the etch dip.

Or about 6% actual FeCl strength. As Kuttler pointed out, 3-4% works. Stronger than 6% and dwell gets too short.

I think Bertram had gotten around to doing it and would have more experience than I by now.

Last edited by Chuck H; 01/03/17 07:11 AM.
Joined: Mar 2013
Posts: 2,862
Sidelock
***
Offline
Sidelock
***

Joined: Mar 2013
Posts: 2,862
Dennis,

Are we talking about Black & White or Brown & White? It's my experience that Brown & White requires longer etching times.

The RS solution does contain a small amount of HCL. I dilute it one more time than what you listed, down to around 3-4%.

Regards
Ken

Last edited by Ken61; 01/03/17 11:00 AM.

I prefer wood to plastic, leather to nylon, waxed cotton to Gore-Tex, and split bamboo to graphite.
Joined: Mar 2002
Posts: 1,815
Likes: 4
Sidelock
**
Offline
Sidelock
**

Joined: Mar 2002
Posts: 1,815
Likes: 4
I use Ferric Chloride 10% as a final wash to increase
contrast WHEN NEEDED. I think I use it more for tighter Damascus(3 and 4 rod) and not the laminated etc. 10% for me seems to be the maximum percentage needed.
When I use it, I wash the bbls and steel wool lightly to help contrast before the Logwood "bath". As mentioned in one of the other posts anything with HCL in it causes RUST.
However any chemical CL after the atomic symbol or compounds symbol is a salt of HCL and requires a nice bath of Baking Soda when you are finished to prevent after rusting.

Last edited by Stallones; 01/03/17 02:39 PM.
Joined: Dec 2001
Posts: 363
Likes: 16
Sidelock
***
OP Offline
Sidelock
***

Joined: Dec 2001
Posts: 363
Likes: 16
And I think my math is a bit off, it should be 71 cc H2O, Oh well.


Dennis Potter

Link Copied to Clipboard

doublegunshop.com home | Welcome | Sponsors & Advertisers | DoubleGun Rack | Doublegun Book Rack

Order or request info | Other Useful Information

Updated every minute of everyday!


Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 0.067s Queries: 31 (0.039s) Memory: 0.8269 MB (Peak: 1.8987 MB) Data Comp: Off Server Time: 2024-03-28 17:31:58 UTC
Valid HTML 5 and Valid CSS