March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Who's Online Now
5 members (Ted Schefelbein, Marc Ret, graybeardtmm3, Ian Forrester, 1 invisible), 832 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums10
Topics38,374
Posts544,009
Members14,391
Most Online1,131
Jan 21st, 2024
Previous Thread
Next Thread
Print Thread
Page 1 of 2 1 2
#540997 03/13/19 10:19 PM
Joined: Nov 2016
Posts: 46
Sidelock
OP Offline
Sidelock

Joined: Nov 2016
Posts: 46
I know this is not exactly gunsmithing but I am needing advice of building a vault room for a gun collection. Wondering about wall dimensions, thickness, materials, vault doors, etc. I am not wanting to sink a fortune but want something relatively fire proof, stout, and obviously theft proof. Thanks hereford

hereford #541095 03/14/19 05:26 PM
Joined: Jul 2012
Posts: 4,445
Likes: 201
Sidelock
**
Offline
Sidelock
**

Joined: Jul 2012
Posts: 4,445
Likes: 201
Hereford,
Do you have a dry basement?

hereford #541198 03/15/19 12:21 AM
Joined: Dec 2001
Posts: 6,264
Likes: 196
Sidelock
***
Offline
Sidelock
***

Joined: Dec 2001
Posts: 6,264
Likes: 196
Lots of information is needed to help. How many guns ?

A couple of general suggestions. If you can, make your ceiling at least 9 feet high. It is so easy to poke holes in low ceilings.
Put in more lights than you think you need, then add some more. The modern non-incandescent bulbs are best as they burn cooler than incandescent lighting. Same advice for electrical receptacles. Add as many as you can.

Joined: Jul 2012
Posts: 4,445
Likes: 201
Sidelock
**
Offline
Sidelock
**

Joined: Jul 2012
Posts: 4,445
Likes: 201
Hereford,
You didn't answer if you have a dry basement. When I built my house, I built an 8'x16' vault in the basement. If you have a basement, I can offer some ideas; if not, I don't have experience.
Mike

Der Ami #541248 03/15/19 01:38 PM
Joined: Feb 2008
Posts: 87
Sidelock
Offline
Sidelock

Joined: Feb 2008
Posts: 87
Mike,
I am not the original poster but would welcome your advise and experience on a vault in a dry basement.
Thanks,
Mike

hereford #541267 03/15/19 04:16 PM
Joined: Dec 2001
Posts: 6,264
Likes: 196
Sidelock
***
Offline
Sidelock
***

Joined: Dec 2001
Posts: 6,264
Likes: 196
There is a ton of information if you google “gun vault construction”

MikeV #541269 03/15/19 05:17 PM
Joined: Jul 2012
Posts: 4,445
Likes: 201
Sidelock
**
Offline
Sidelock
**

Joined: Jul 2012
Posts: 4,445
Likes: 201
Mike V.
If you have a basement with masonry walls, you already have two walls of your vault in a corner. When I built my house, I set rebar in the concrete floor for the inside walls, but you can drill and place rebar with "Setcrete" into the existing floor. The easiest way is to lay 8"x 16" concrete block with vertical rebar @ 8" o/c( one in each cell of the blocks, and wire ladder reinforcement in every other course( every 16"). In an existing home, the ceiling will be much harder than mine, where I could pour concrete without the obstruction of the floor above. You will have to evaluate your own situation and decide between 3 choices. If you want a concrete ceiling, you will have to build a form, using either 4x4 or 2x4 and 1x4 cross bracing. I used 2x4 @ 16 o/c, because I was going to have a use for them during the rest of the construction. You will have to "worry" 3/4" plywood overhead during the placement of the posts, or place them over the top of the walls by leaving the last course of block until after setting the form. You will need to think backward with the idea of being able to wreck( remove) the form. You don't want to have to resort to chisels. Be sure to run conduit for an overhead light and a convenience outlet for a dehumidifier. While you are laying the walls, make arrangements for a drain, so you won't have to empty the dehumidifier manually( it will run over otherwise). You can drill anchors into the existing walls, to tie the new walls in. Since you will be limited for "headroom", you will need to use short sections of vertical rebar and tie( wire) them together as you go up, and fill the cells in the block course by course as you go up. People that sell gun safes also sell vault doors, so you should talk to one of them in the beginning of the project to find the dimensions you need for the opening. Someone above recommended a 9' ceiling. You are not likely to achieve this, you will be lucky to get 7 1/2'( 6 1/2-7 is more likely). You will have to pour the concrete for the ceiling over the top of the wall, so you should orient the vault so that the joists of the floor above run with the short side, to make pouring the concrete a little easier.
A second option is to anchor angle sections to the walls and fabricate a steel ceiling, from what ever is available to you. I have seen them built from PSP( pierced steel planks- airfield matting) and can understand using bars or plates. The comments on lights, door opening dimensions and drain still apply.
A third option is to just make the walls run to the joists above and place a ceiling in the room outside and one inside the vault, hiding the lack of a secure ceiling. The other comments apply here too.
Are we confused yet?
Mike

hereford #541273 03/15/19 05:34 PM
Joined: Nov 2016
Posts: 46
Sidelock
OP Offline
Sidelock

Joined: Nov 2016
Posts: 46
Sorry to respond so late but my on call schedule has been pretty rough. I have a huge basement but it's relatively high moisture and has a history of water in the past so I'm a bit concerned of that. It's an 1850 plantation home so I was figuring an addition. I want room for 100 plus guns as I'm realitivy young and already have over 50. Thanks hereford

hereford #541286 03/15/19 07:29 PM
Joined: Feb 2008
Posts: 87
Sidelock
Offline
Sidelock

Joined: Feb 2008
Posts: 87
Mike,
Thank you for the reply. It is very helpful, most especially the info on building the ceiling. That has been where I have been a bit stumped.
Mike

hereford #541298 03/15/19 09:29 PM
Joined: Jun 2008
Posts: 5,522
Likes: 167
Sidelock
**
Offline
Sidelock
**

Joined: Jun 2008
Posts: 5,522
Likes: 167
Expanded steel mesh lag screwed with washers onto walls and ceiling

https://www.metalsdepot.com/steel-produc...FBoCmPYQAvD_BwE

And 5/8 inch fire rated sheet rock

Last edited by skeettx; 03/15/19 10:54 PM.

USAF RET 1971-95 [Linked Image from jpgbox.com]
Page 1 of 2 1 2

Link Copied to Clipboard

doublegunshop.com home | Welcome | Sponsors & Advertisers | DoubleGun Rack | Doublegun Book Rack

Order or request info | Other Useful Information

Updated every minute of everyday!


Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 0.063s Queries: 36 (0.039s) Memory: 0.8514 MB (Peak: 1.8987 MB) Data Comp: Off Server Time: 2024-03-28 20:56:52 UTC
Valid HTML 5 and Valid CSS